Some notices for drilling mud agitator buyers

The mud agitators are high-efficiency mud-mixing units which used for stiring mud slurry to maintain suspension of solids .The agitator is mounted on top of the mud tank and has one or two impeller immersed in the mud slurry. Mud mixing tank is working to keep drilling mud balance by add some chemicals. While drilling mud stay in tank , it will need mud agitators to avoid sedimentation.
Mud agitators utility notes for buyers:
1, check whether the mud agitator selection is correct, the actual conditions of use are consistent with the specified conditions of use.
2, the stirrer motor and two hard steel cable protection metal hoses in the mud tanks, to ensure sealing pipe connections.
3, with 0-500V Megger, check the motor three main cable wire insulation resistance of not less than 5 megohms, disabled Megger check control cables, submersible mixer avoid damage to the internal electrical components, and applications multimeter check control cable.
4, if the power supply using the distance from the mud agitator far, considering the line loss, cross-sectional area cable should be increased, the joints should be as little as possible and fittings for sealed to prevent leakage.
5, mud agitator power cable on the ground and control cables should control cabinet (box) wiring head butt one.
6, mud agitator grounding line color line (yellow / green), in order to ensure safety, must be connected securely, and grow than other lines 50mm.
7, stirrer control a fine thick cable of mud agitators, measured with a multimeter off, three of them with two fine pass for temperature measurement signal line, a color line and the signal line does not make sense for the leak.
8, mud agitator before final installation, facing the direction of the impeller, the impeller rotates counterclockwise. If the rotation direction is incorrect exchange position on the control cabinet or terminal box in any of the three-phase line two lines, you can change the direction of rotation. If several mud agitator mixers connect to a control cabinet or terminal box on the mud agitator mixer each station must be checked individually.
9, after the closing, the mud agitator cannot start immediately, should be through mud mixer control system self-test, if there is a fault (flashing alarm or alert warning appears on the cabinet), you should check and troubleshooting, and then only start If the motor does not turn, should quickly and decisively to wind up, you should check the troubleshooting, to avoid damage to the motor.
10, the stirrer of mud agitator started, should observe the motor and circuit voltmeter and ammeter, if abnormal, should immediately stop identifying the reasons for closing the troubleshooting before being re- start.
11, a few mud agitator cannot start together, you should start one by one.
KOSUN can manufacture types of drilling fluid solids control systems according to the requirements of different drilling conditions. KOSUN is well-know as a professional manufacturer and supplier of oil drilling solids control equipment in China. After 20 years development,KOSUN is becoming more and more stronger,can provide more efficient equipments at the same time, the products including drilling shale shaker, shale shaker screen, desander, desilter, vacuum degasser, centrifugal pump, submersible slurry pump, shear pump,mud agitator, mud gun, drilling fluid cleaner,drilling decanter centrifuge, jet mud mixer, mud tank, diesel tank, water tank, complete solids control system,etc.


http://www.china-kosun.com/kosun-solids-control-equipment/shear-pump.html

KOSUN three kinds of drilling solids control systems' advantages

KOSUN solids control system includes Skid-mounted Solids Control System,mobile solids control system and arctic solids control system. Skid-mounted Solids control system performance and quality is the key to the drilling fluid system technology. Mobile oilfield solids control system to adapt to the operation time limits, to improve the speed of mobilization and to reduce the cost.To meet the requirements of the polar cold (minus 40 degrees centigrade) working conditions, KOSUN is able to customize arctic solids control system to produce the arctic solids control system which is solely applied under extremely cold temperature.
KOSUN Skid-Mound solids control system
1.Easy to assemble: The skid-mounted drilling solids control system is generally manufactured and assembled in factory. Its assembly would not take much time since it could be put into use after interface pipelines and outer electric appliances are connected.
2.Easy to move: it may be easily moved since all its functional components are integrated on one base.
3.Compact in design: its footprint is not much: the skid-mounted drilling solids control system equipment is compact in design so that much less space would be taken up compared with the traditional assembly method of it.
KOSUN Arctic solids control system
1.Easy to assemble: The skid-mounted drilling solids control system is generally manufactured and assembled in factory. Its assembly would not take much time since it could be put into use after interface pipelines and outer electric appliances are connected.
2.Easy to move: it may be easily moved since all its functional components are integrated on one base.
3.Flexible: KOSUN 1000GPM Orbit Arctic Solids Control System can do group drilling for 10 wells at the same time.No.1 tank of the solids control system is connected at its end via a jointing lug to the hydraulic cylinder, which will lead it to move on the orbit.
KOSUN Mobile solids control system
1.Easy to move: it can be installed and flexibly moved on various trailers (like, tire trailer, skid trailer, etc.)
2.Compact in design: the skid-mounted principle is applied on it since it may be easily moved with all its functional components integrated on one base.
3.Easy to assemble: it is generally manufactured and assembled in factory and its assembly would not take much time.
In China solids control industry, KOSUN is a solids control leader and expert in drilling waste management. KOSUN is capable of providing customers with such four series as oil & gas oilfield solids control equipment, centrifuge, drilling waste treatment equipment and drilling security equipment, including 25 categories of products,such as drilling shale shaker, shale shaker screen, desander, desilter, vacuum degasser, centrifugal pump, submersible slurry pump, shear pump,mud agitator, mud gun, drilling fluid mud cleaner, decanter centrifuge, jet mud mixer, mud tank, diesel tank, water tank, complete solids control system,etc.


http://www.china-kosun.com/news/kosun-oilfield-mud-cleaner.html

Specifications of KOSUN drilling mud tanks

Drilling fluid solid control system is an requisite part in modern drilling. It will ensure the slurry of the normal circulation and stability in the process of drilling rigs. the product is mainly made up of explosion-proof driving force, electric distribution and lighting control devices, new dual-layer and dual-excitation shale shaker, centrifugal vacuum degasser , desander, desilter , horizontal centrifuge, vertical sand pump, slurry mixers, mixed feeder funnel, cycle tanks, and other solid control equipments and so on. It can effectively separate and mix round and store drilling fluid, to meet the needs of drilling project. And we absorb and develop a complete set of solid control system, as ZJ40J, ZJ50D, ZJ70D, ZJ32, ZJ20B7 models.
The mud tank main features:
Using V corrugated plate , the excellent whole rigidity , beautiful appearance .
Surface of the tank with water pipeline and intermediate pressure slurry pipeline.
Tank with heating pipes to ensure the normal operation in cold season.
The sand cleaning door is in tank, convenient and flexible to open.
The union joints between tanks is the hard pipeline connection ,easy disassembly and good flexibility.
Tanks with the mixers, new-style slurry gun and a cone-shaped feeder funnel , which can be adjusted and maintained the performance of drilling fluid , further more be convenient to clean.
We can produce in accordance with the special requirements of the user; the entire tank can be made strictly in accordance with the HSE system, Aesthetic appearance, the advanced process , completely can meet the demand of the processing of oil drilling technics to sullry.
Mud Tank Specifications
1. centralized electric control;
2. can complete weighting, mixing, solid-liquid separating, degassing and other processes;
As a mud carrier, mud tank is an indispensable part of mud circulation system and it can complete weighting, mixing, solid-liquid separating, degassing and other processes. Mud tank can carries the mud circulating between well head and mud pump.
* The solid phase particles in mud will be separated stage by stage through relevant solids control equipment on mud tanks as to make the fluid meet drilling requirements after mixing and weighting system.
In China solids control industry, KOSUN is a solids control leader and expert in drilling waste management. KOSUN is capable of providing customers with such four series as oil & gas drilling solid control equipment, centrifuge, drilling waste treatment equipment and drilling security equipment, including 25 categories of products,such as shale shaker, shale shaker screen, desander, desilter, vacuum degasser, centrifugal pump, submersible slurry pump, shear pump,mud agitator, mud gun, drilling mud cleaner, drilling centrifuge, jet mud mixer, mud tank, diesel tank, water tank, complete solids control system,etc.